湖南快乐十分官网

你好,欢迎浏览济南恒鑫刀具回收有限公司网站!
数控刀片回收

专心 专注 专营

服务好 效率高 诚信好 价格高

数控刀片回收

联系电话:

湖南快乐十分官网18605312229

当前位置:湖南快乐十分官网>湖南快乐十分官网>湖南快乐十分官网>数控刀片的这些问题,你遇到过吗?

数控刀片的这些问题,你遇到过吗?

来源:http://www.bargainillion.com/ 日期:2019-12-03 发布人:admin

  数控刀具是金属行业常用的刀具,日常的数控生产离不开他,在使用过程中进程会出一些小问题,今天就让我们来一起看一下这些常见问题,又怎么去排除它:

  CNC tools are commonly used tools in the metal industry. They are indispensable for daily CNC production. There are some small problems in the use process. Today, let's take a look at these common problems and how to eliminate them:
数控刀片回收,数控刀具刀片回收
  1刀片在运转时有跳动处理;
  1. The blade has run out treatment during operation;
  1.1检查刀片安装是否到位。
  1.1 check whether the blade is installed in place.
  1.2检查切脚机工作安装面是否有杂物。
  1.2 check whether there are sundries on the working and installation surface of the foot cutting machine.
  1.3检查内径与转动轴之间间隙。
  1.3 check the clearance between the inner diameter and the rotating shaft.
  2刀片裂纹;
  2 blade crack;
  2.1使用前:手指手指钩起刀片用木锤轻轻敲几下,听声音。
  2.1 before use: pick up the blade with fingers and fingers and tap it gently with a wooden hammer to listen to the sound.
  2.2使用后:安装时可否因安装面存有硬物,固定时用力而导致刀片裂开。
  2.2 after use: can the blade be cracked due to hard objects on the mounting surface and force during fixing.
  2.3除上述两种情况,可否因人为摔坏或刀片本身就有问题。
  2.3 in addition to the above two situations, whether the blade is broken due to human reasons or there is a problem in itself.
  3刀片有缺口;
  3. The blade has a gap;
  3.1切脚机没有进行5分钟空转而开始进行工作。
  3.1 the foot cutting machine did not idle for 5 minutes and began to work.
  3.2元件脚直径太大,可通过调整刃口的角度来处理,具体角度要根据元件脚直径大小来定。
  3.2 if the diameter of component foot is too large, it can be handled by adjusting the angle of blade. The specific angle shall be determined according to the diameter of component foot.
  4元件脚切不断;
  4. Continuous cutting of element feet;
  4.1是整块PCB元件脚或部份得分清楚,检查PCB板厚度和材质,是否因高温焊接过程中PCB变形而导致。
  4.1 the whole PCB component pin or part shall be scored clearly, and the thickness and material of PCB shall be checked to see whether the PCB is deformed during high temperature welding.
  4.2 轨道与刀片的距离间隙可调小。
  4.2 the distance gap between the rail and the blade can be adjusted to be small.
  4.3是否刀片使用时间过长,出现小缺口,而未磨。
  4.3 whether the blade has been used for a long time, with small gap but not worn.

88彩票app下载 众彩彩票注册 湖南快乐十分 湖南快乐十分官网 湖南快乐十分走势图 万利彩票app 湖南快乐十分 湖南快乐十分 湖南快乐十分官网 湖南快乐十分走势图